Applications /AUXILIARY SKID CONTROL

See which step is waiting—and why.

A wash-water skid is waiting to run. The start command alone cannot explain whether a valve confirmed its position. A local command-and-feedback sequence gives maintenance a more precise question to investigate.

Paper-mill auxiliary systemsProposed application pilot
Paper-mill auxiliary systems

What this could improve for your team

Potential benefits to test on your equipment, with results measured against your requirements.

Erik finds the waiting stepAn illustrated story with narration
  1. The wash has not started

    A paper mill has a short window to wash an auxiliary line. Erik reaches the skid, but the next step has not started. His colleague has pressed start twice. What is it waiting for?

Illustrative development concept

Read the full narration
  1. 00:00
    The wash has not started

    A paper mill has a short window to wash an auxiliary line. Erik reaches the skid, but the next step has not started. His colleague has pressed start twice. What is it waiting for?

  2. 00:12
    Which confirmation is missing?

    Erik follows one small sequence: request the valve, confirm its position, then permit the external pump drive. A command and a confirmation are different. Seeing that distinction would narrow the first check.

  3. 00:25
    Decide locally at the skid

    For a replacement skid, Erik discusses bootctrl’s controller design. The base would run the sequence locally. Its switching module would handle compatible valve and drive commands, with digital feedback returning to the same controller.

  4. 00:40
    Test the waiting conditions

    Their evaluation includes missing feedback, delayed movement and restart conditions. A scoped platform connection could show selected commands and responses to maintenance. It would explain the waiting step, not diagnose a faulty valve.

  5. 00:55
    Start with the relevant check

    Back at the skid, his colleague could begin with the relevant position switch or actuator connection, following the site procedure. The team keeps responsibility for the inspection and for independent plant safety.

  6. 01:07
    Use the maintenance window well

    The aim is less blind restarting and a clearer check. Erik’s experience becomes a sequence his colleague understands, rather than an explanation that disappears after the shift.

  7. 01:19
    Choose one auxiliary sequence

    Which auxiliary sequence wastes your mill’s maintenance time? Bring bootctrl the valve commands, feedback and external drive interface. Start with one manageable skid, not an entire paper machine.

Synthetic narration · Voice credits

Start with the right check

Distinguish the command, the expected confirmation and the next permitted step. Narrow the inspection to the relevant interface.

Make fault handling explicit

Agree what should happen when a confirmation is absent or late, then test that behaviour before field use.

Carry the method forward

Keep the step definitions and inspection notes useful for the next technician. Platform history is an optional integration.

How it could work in practice

  1. Map one auxiliary sequence

    Define the valve command, position confirmation and external pump permit, with load and timing requirements.

  2. Try missing and delayed feedback

    Use a controlled test setup to evaluate waiting states, timeouts and rearming. The hardware and application firmware still require qualification.

  3. Prepare a focused maintenance check

    Use the recorded step and feedback state to choose a physical inspection. Do not infer a diagnosed valve fault from one missing signal.

Proposed application pilot

The opportunity

A paper mill has a short window to wash an auxiliary line. Erik reaches the skid, but the next step has not started. His colleague has pressed start twice. What is it waiting for? Erik follows one small sequence: request the valve, confirm its position, then permit the external pump drive. A command and a confirmation are different. Seeing that distinction would narrow the first check. For a replacement skid, Erik discusses bootctrl’s controller design. The base would run the sequence locally. Its switching module would handle compatible valve and drive commands, with digital feedback returning to the same controller. Back at the skid, his colleague could begin with the relevant position switch or actuator connection, following the site procedure. The team keeps responsibility for the inspection and for independent plant safety. Which auxiliary sequence wastes your mill’s maintenance time? Bring bootctrl the valve commands, feedback and external drive interface. Start with one manageable skid, not an entire paper machine.

Signals to work with
Wash request, valve-position switches and external pump-drive readiness. Add compatible flow or pressure transmitters only where the sequence needs them.
The record to aim for
A timestamped sequence log showing the requested valve state, received confirmation, waiting step and permitted restart after an inspection.
Development status
Proposed auxiliary-skid evaluation on P.13 development hardware. Timeouts, rearming and field interfaces require testing before plant use.
Modular industrial controller
Why start here

Auxiliary equipment provides a manageable boundary for testing local sequences and fault handling without redesigning the entire production line.

A practical next step

What would you like your machine to do better?

Bring a machine sequence, a movement challenge, a structural test or an equipment-service question. Let’s define a useful first evaluation.

Discuss your application
Contact options

Existing customer services

This service has no public link yet. Use the contact page to ask about access.

support@bootctrl.comAbout & contact
Open larger image